BEST ACCESS RAMPS | ROADSIDE CURB RAMPS | ALUMINIUM EXTRUSION RAMPS | BEST CUSTOM CAR RAMPS | METAL DRIVEWAY RAMP
Want The Best Roadside Kerb Metal Access Ramps for your home entrance situation?
Best Access Ramps KERBY™ is the best looking Aluminium Ramp around that is customisable and suitable for almost all situations, designed to stop the annoying bump and you bouncing, bottoming out or scraping your car!
Best Access Ramps KERBY™ is designed right here in Rolleston (Selwyn, Christchurch NZ), custom made for your situation – to nearly smooth out and banish that bump to stop your precious car bouncing, bottoming out and scraping! These are the best Aluminium metal driveway ramps on the market!
We had ‘had enough’ of that b@$stard “bump” every time we went in or out of our driveway which kept destroying our wheel alignment each month, therefor making our car steer badly and our tyres wear out faster. I used to spend heaps on wheel alignments and new tyres. “Enough!” we said, let’s design the best Access Ramps in New Zealand we can imagine, so we did – it’s better than awesome I reckon!
“Whatever the application for Metal Driveway Ramps: best access ramps, forklift ramps, kerb ramps, roadside ramps, entry ramps, garage door entrance ramps, curb or driveway ramps for your garage or even wheelchair access. We even use make custom ramps for caravan or motorhome – you name it, we make it, it works!”.
BEST ACCESS RAMPS KERBY™ – Metal Driveway Ramp
The Best way to stop your wheels going out of alignment and stop bottoming out and scraping your precious lowered car!
Best Access Ramps (KERBY™) is a super-strong Metal Driveway Ramp made from Aluminium Extrusion, Fixed Access Ramp, for your driveway gutter kerb. Best Access Ramps system that fixes into the gutter area with 10mm sleeve anchors (Dynabolts), or sometimes concrete screws, to enable a superior smoother, safer transition over the curb/gutter. So no more bumping – KERBY BANISHES THAT B@$TARD BUMP! – and no more grinding the front off your car off, no more bouncing the trailer over the curb, and no more expensive wheel alignments all the time! In fact, you can get on and off the road faster, smoother, quieter and more safely with confidence. You’ll forget it’s even there!
Best Access Ramps (KERBY™) is far superior to any other bent flat Mild Steel metal driveway ramps (that go rusty and sag), rubber ramp or Mild Steel/Galvanised tread-plate folded driveway kerb ramps that degrade or sag and bend easily and quickly over time – they don’t look good and don’t keep performing. We’re all about good looks and first impressions right? KERBY™, The Best Driveway Ramps solves this problem and are in my opinion, are the best looking, most flexible and durable Aluminium Fixed Ramp Extrusion option on the market that I know of. KERBY™ is designed to take even the heaviest truck. KERBY™can be ordered in many different ways and lengths to best suit you and your situation. You can even use off-cuts as trailer or caravan chocks and teenager car stoppers in the garage.
The image on the left is an example of a Standard Straight Powder-coated KERBY™ install and has been powder coated the same colour as this customers garage (Ebony/Black textured like Teflon).
Additionally I can put Hazard tape on them or even Glow-In-The-Dark Tape Stripe so you can see it at night, which is pretty cool (see the pricing area below)!
Contact me now for a FREE measure-up and quote, click here…
The Best Roadside Gutter Kerb Driveway Access Ramp KERBY™
Car bottoming out or scraping, need quicker smoother, SAFER access, or simply just want to BANISH THAT B@$TARD BUMP?!
These heavy duty Metal Driveway Ramps made from Aluminium extrusion: Gutter Ramps, Kerb ramps, kerb ramp idea or curb ramp ideas, whatever you want to call them are designed to solve many problems, like BANISHING ’THE B@$STARD BUMP’ as you drive in and out, stopping trailer noise, stopping the damage of scraping or bouncing over the kerb, and saving your expensive wheel alignment, in turn saving your tyres. KERBY™ looks and performs the best and is far cheaper than flat metal ramps.
Why risk scraping the bottom of your car and damaging your car and driveway, every time you pull in or out of your home?
Stop bottoming out, scraping, bouncing & bumping over the kerb, and making banging noises when you drive in and out of your house, especially with a trailer. Stop that annoying bump and fill the gap between your driveway and the street access with a smooth, easy speedy, and safe entry and exit with KERBY™ – the best driveway ramp that is based in Rolleston Christchurch, NZ and can be installed locally at your place in a flash.
The image to the right is an example of a Custom Concave Curved Install.
Contact me now for a FREE measure-up and quote, and eliminate that annoying bump in your driveway kerb…
What's the cost of The Best Driveway Ramp in NZ?
KERBY™ Gutter Ramps Pricing
The Best Driveway Access Ramps, KERBY™ are a hollow extrusion made from the highest quality, 6mm thick, T6 Aluminium which comes in 4m (Option A* – The Default Length) standard lengths and that we can mix and match and cut to multiple sized items in many combinations to suit your driveway width and curve. Please see the T&C’s as to what a Standard Install v a Customised install is.
The size of a KERBY™ is 50mm High x 100mm Deep, by 4m length as standard, which of course can be cut down into increments of .5m, 1m, 2m, or 3m lengths.
There are three styles you can order KERBY™ in…
A “CLEAN” length or section has NO FIXING HOLES – For Serious Full-On DIY’ers who have all the special tools.
Professionally “PRE-DRILLED” with Fixing Holes – You can DIY install these yourself but you’ll need all the special tools (see below).
“INSTALLED” – We do it all for you, everything is included.
I just need to know your physical address, an email address for the quote, and the total width of the driveway/access point, plus a configuration of KERBY™ length(s) that may be required etc, see our quote/order form here. I will also need to see a phot or two to base the quote on. That can be sent to me from here.
KERBY™ Driveway Ramp Prices
Configurations & Styles
Click on a colour below to reveal the current pricing (subject to change at short notice due to fluctuations in Aluminium prices)
NO FIXING HOLES – Full-on DIY – Straight from the factory
CLEAN DIY LENGTHS
Clean no-hole lengths straight from the factory for the Full-on serious DIY-er
| Length | Detail | Price |
| 1m | 1x 1m length for a Slightly Curved or a Standard Straight entry | $200+GST |
| 1.5m | 1x 1.5m length for a Slightly Curved or a Standard Straight entry | $275+GST |
| 2m | 1x 2m length for a Slightly Curved for a Standard Straight entry | $350+GST |
| 3m | 1x 3m length for a Standard Straight entry | $500+GST |
| 4m–A* | 1x 4m-A length for a Standard Straight entry | $600+GST |
| 4m–B | 1x 3m + 1x 1m lengths for a Standard Straight entry | $700+GST |
| 4m–C | 2x 2m lengths for a Standard Straight or Slightly Curved entry | $700+GST |
| 5m | 1x 4m-A + 1x 1m lengths for a Standard Straight entry | $800+GST |
| 6m–A | 1x 4m-A + 1x 2m lengths for a Standard Straight entry | $950+GST |
| 6m–B | 3x 2m lengths for a Slightly Curved for a Standard Straight entry | $1,100+GST |
| 6m–C | 4× 1.5m lengths for a Slightly Curved for a Standard Straight entry | $1,100+GST |
| 7m | 1x 4m-A + 1× 3m lengths for a Standard Straight entry | $1,100+GST |
| 8m | 2x 4m-A lengths for a Standard Straight entry | $1,200+GST |
| 9m | 3x 3m lengths for a Slightly Curved or a Standard Straight entry | $1,400+GST |
| 10m | 2x 4m-A + 1x 2m lengths for a Standard Straight entry | $1,550+GST |
CLEAN DIY LENGTHS will need to be Pre-Drilled twice and installed by yourself into the concrete by using Sleeve Anchors, or you can ask a local friendly builder who like scones.
For Skilled DIY-ers
DRILLING
TOOLS NEEDED: You will need a Drill Hole Punch Marker for steel or similar, or a Sharpie Marker to mark out where you want to drill all the holes. You will need a 20mm Starret Hole Saw or large Drill Bit or similar from an engineer type shop (that’s a big 20mm one, double the size of normal! That’s about $25 last time I looked). You will also need a normal type drill that can drill at least a 20mm top hole and a standard 11mm bottom hole perfectly level/perpendicular through the top of angled 6mm Kerby™ extrusion (preferably a corded/powered style as battery styles take so long and are usually under-powered). I use a drill press to achieve this to get all the holes level and perfectly aligned and centred, otherwise it makes installation life a bit of extra admin putting it lightly.
METHOD: Firstly, on the top of the 6mm extrusion between the top two spaced out ribs, where the only grove is (as a guide), mark where you want all the holes to be along the length on that groove line, all spaced out as suggested (following this) with a Drill Hole Punch Marker or Sharpie Marker. The hole sets are normally 100mm from each end, then spaced out at every metre. EG: Hole configuration on a 4m length from the first end to the last end is: 100mm | 1000mm | 2000mm | 3000mm | 3900mm*. *100mm in from the last end. Secondly, drill your top holes of 20mm with a hole saw or similar, and then a bottom hole of 11mm all the way through the bottom through the same centre line. Clean up as the Aluminium swarf and filings go absolutely everywhere! That’s a Health & Safety warning for your wife. It follows me into the house and is a nightmare to get it out the carpet! Trust me, you do not want that!
FIXING IN PLACE
TOOLS NEEDED: Fixing as per how many holes you will have in the total length(s). Only the best 316 Stainless Steel Sleeve Anchors are supplied as extras (additional cost) as standard, at a very special rate (cheaper than Bunnings or Mitre 10 etc) on the Quote. NB: If you are supplying the fixings yourself, do not use Plain Steel, Zinc Coated or Galvanised Sleeve Anchors as they react with the Aluminium and corrode and rust etc (weaken and move). If the length(s) move, they will continue to get worse and squeak and carry on each time someone drives over the installation. You will also need a 13mm tube socket for the Sleeve Anchors, with a diameter no more than 20mm to get through the 20mm top hole of the Kerby™ that you are going to drill out (these are about $50 last time I looked), and a Ratchet (these are also about $50 last time I looked). You will need a special “Hammer” type drill that vibrates and can drill at least a 10mm hole in the concrete (power or battery style) to a depth of 100mm-110mm. You will need a special 10mm 4-Tipped Concrete Drill Bit of at least 150mm long. This goes faster and better than a 10mm 2-Tipped version. These are normally $25 each last time I looked. You will need a 6mm-12mm Hammer Punch to hammer the Sleeve Anchors in place through the holes. These are about $60 last time I looked. You need a rag and something like Turps to clean up the surface of the KERBY™ to finish off. And water for you!
METHOD: Lay down the Clean length(s) where you want the ramp to be (according to the specifications drawing on this website below, to at least 30mm out from the edge of the kerb for water and leaf debris. This also makes for a better, softer angle.). Pre-Drill the 10mm concrete holes to about 10mm deep, to pre-mark out where you want the final concrete holes to be through the Pre-Drilled holes of the extrusion’s 20mm top holes and 11mm bottom holes. This marks out where you want the finished concrete holes to be, better than poking a Sharpie Marker through the holes from the top, the concrete destroys them! Move the lengths away again and finish drilling the 10mm concrete holes to a depth of at least 100mm-110mm deep. Remove dust and waste, a leaf blower works great! Lay the lengths back down again in place. Put the Sleeve Anchors in place through the top hole, through the bottom hole into the concrete. Hammer them all the way in with a Punch or similar until you hear a “ting!”, that’s when the washer touches the extrusion, then they are firmly all the way down and in place. You will need a 13mm tube socket with a diameter of 20mm or less to fit through the top hole to fix the 10mm Sleeve Anchors nuts onto the 11mm bottom holes into the 10mm concrete holes. Tighten them up slowly until slightly firm and they grip. Sometimes, you get one that doesn’t grip, I do not know why, by at this point I have to take it out and add an epoxy glue to make sure it stays in place, as to not weaken all the rest of the length(s). $10 from the Warehouse is fine and sets in 5-20 minutes, enough to tighten it up again as to just before gripping, then wait for the glue to go off (meantime keep reading…). Walk and jump along the ramp length to possibly jiggle it down further to suit the variable undulations (concrete is never perfectly flat!). Go back to the first Sleeve Anchor and firmly tighten them all up from there – not too tight – my socket does a “click” when I then know it’s ‘just right’! From firm to tight, then an extra quarter turn I find. Lastly, and the best bit, put all the Black Nylon Hole Covers in the 20mm top holes to make it look sexy. Wipe all the surfaces down to get rid of the grease. Job done! Ready to go! You will forget it’s there after a week or so.
Usage
With CLEAN LENGTHS can also be used for wheel chocks for your classic car in the garage to stop you backing back or forward too much, caravan ramps, motorhome or trailer ramps, RV ramps, garden shed ramp for the mower etc. Great for your teenagers to learn how far to go into the garage to park the car the easy way. This way you feel when to stop. Looks way better too! A modern version of that old-stool tennis ball on a string hanging down from the ceiling that touches the wind screen that tells you when to stop.
*4m-A is the Standard Clean (no holes) Un-Cut whole standard Length of KERBY™ is as it comes supplied from the mill. The 4m-A can be cut down or added to to make all the various different configurations. The pricings are all based on using a 4m-A Length economically to eliminate waste.
FIXINGS & FINISHERS ARE ADDITIONAL
M10x50 316 Stainless Steel Sleeve-Anchors (Dynabolt fixings) to suit how many holes you have, can be supplied at a very special price of $8.00+GST each hole. At Mitre 10 or Bunnings, last time I looked were $20 for two! Nylon Dome Hole Covers (Black) to suit how many holes you have, can also be supplied at a very special price of $0.50+GST each hole. Both will be additionally added to the quote sent to you as standard, unless otherwise agreed upon.
NB: Aluminium prices fluctuate, so please bear with us if the prices go up again (it is out of our control). Freight/shipping and custom or ‘tricky’ installation costs vary and are additional. All prices are +GST and are subject to change.
WITH FIXING HOLES - Easy DIY
Pre-Drilled KERBY™ Prices
Pre-Drilled Lengths with 20mm Top Holes and 10mm Bottom Fixing Holes for easy DIY installing*
| Length | Configuration | Price |
| 1m | 1x 1m length (2 Holes) for a Slightly Curved or a Standard Straight entry | $250+GST |
| 1.5m | 1x 1.5m length (3 Holes) for a Slightly Curved or a Standard Straight entry | $350+GST |
| 2m | 1x 2m length (3 Holes) for a Slightly Curved or a Standard Straight entry | $450+GST |
| 3m | 1x 3m length (4 Holes) for a Slightly Curved or a Standard Straight entry | $650+GST |
| 4m–A* | 1x 4m-A length (5 Holes) for a Standard Straight entry | $800+GST |
| 4m–B | 1x 3m + 1x 1m lengths (6 Holes) for a Standard Straight entry | $900+GST |
| 4m–C | 2x 2m lengths (6 Holes) for a Slightly Curved or a Standard Straight entry | $900+GST |
| 5m | 1x 4m-A + 1x 1m lengths (6 Holes) for a Slightly Curved or a Standard Straight entry | $1,050+GST |
| 6m–A | 1x 4m-A + 1x 2m lengths (8 Holes) for a Slightly Curved or a Standard Straight entry | $1,250+GST |
| 6m–B | 3x 2m lengths for a slight curve (10 Holes) for a Slightly Curved or a Standard Straight entry | $1,400+GST |
| 6m–C | 4x 1.5m lengths for a slight curve (12 Holes) for a Slightly Curved or a Standard Straight entry | $1,400+GST |
| 7m | 1x 4m-A + 1x 3m lengths (9 Holes) for a Standard Straight entry | $1,450+GST |
| 8m | 2x 4m-A lengths (10 Holes) for a Slightly Curved or a Standard Straight entry | $1,600+GST |
| 9m | 2x 4m-A + 1x 1m lengths (12 Holes) for a Standard Straight entry | $1,850+GST |
| 10m | 2x 4m-A + 1x 2m lengths (13 Holes) for a Standard Straight entry | $2,050+GST |
Pre-Drilled KERBY™
With PRE-DRILLED (DIY) lengths you need a 20mm diameter long 13mm tube socket to fix the supplied 316 Stainless Steel Dynabolts (Sleeve Anchors) in place through the top of KERBY™’s 20mm top hole, into the 10mm pre-drilled base holes; M10x50 (10mm x 50mm long) 316 Stainless Steel Dynabolts (Sleeve Anchors) and Nylon Black Hole Covers (Caps) are all included and supplied as standard additionally as a part of the final quote, typically as per how many holes you have. 316 Stainless Steel Dynabolts (Sleeve Anchors) are normally $10+GST retail each! You will also need a 10mm concrete drill bit for drilling 100mm deep holes in the gutter area concrete. NB: to start, measure 30mm away from the Curb side, place the KERBY™ down to double-check and mark the KERBY™ holes in place on the concrete in dry weather with a sharpie marker. You will need to clean the concrete area before you start – to be free from leaves, stones, dust and debris – and after you drill, to then place the KERBY™ in place to be ready to install.
NB: FIXINGS ARE ADDITIONAL
M10x50 316 Stainless Steel Sleeve-Anchors (Dynabolt fixings) to suit how many holes you have, can be supplied at a very special price of $8.00+GST each hole. At Mitre 10 or Bunnings, last time I looked were $20 for two! Nylon Dome Hole Covers (Black) to suit how many holes you have, can also be supplied at a very special price of $0.50+GST each hole. Both will be additionally added to the quote sent to you as standard, unless otherwise agreed upon.
Installing: FIXING IN PLACE
TOOLS NEEDED: Fixing as per how many holes you will have in the total length(s). Only the best 316 Stainless Steel Sleeve Anchors are supplied as extras (additional cost) as standard, at a very special rate (cheaper than Bunnings or Mitre 10 etc) on the Quote. NB: If you are supplying the fixings yourself, do not use Plain Steel, Zinc Coated or Galvanised Sleeve Anchors as they react with the Aluminium and corrode and rust etc (weaken and move). If the length(s) move, they will continue to get worse and squeak and carry on each time someone drives over the installation. You will also need a 13mm tube socket for the Sleeve Anchors, with a diameter no more than 20mm to get through the 20mm top hole of the Kerby™ that you are going to drill out (these are about $50 last time I looked), and a Ratchet (these are also about $50 last time I looked). You will need a special “Hammer” type drill that vibrates and can drill at least a 10mm hole in the concrete (power or battery style) to a depth of 100mm-110mm. You will need a special 10mm 4-Tipped Concrete Drill Bit of at least 150mm long. This goes faster and better than a 10mm 2-Tipped version. These are normally $25 each last time I looked. You will need a 6mm-12mm Hammer Punch to hammer the Sleeve Anchors in place through the holes. These are about $60 last time I looked. You need a rag and something like Turps to clean up the surface of the KERBY™ to finish off. And water for you!
METHOD: Lay down the Clean length(s) where you want the ramp to be (according to the specifications drawing on this website below, to at least 30mm out from the edge of the kerb for water and leaf debris. This also makes for a better, softer angle.). Pre-Drill the 10mm concrete holes to about 10mm deep, to pre-mark out where you want the final concrete holes to be through the Pre-Drilled holes of the extrusion’s 20mm top holes and 11mm bottom holes. This marks out where you want the finished concrete holes to be, better than poking a Sharpie Marker through the holes from the top, the concrete destroys them! Move the lengths away again and finish drilling the 10mm concrete holes to a depth of at least 100mm-110mm deep. Remove dust and waste, a leaf blower works great! Lay the lengths back down again in place. Put the Sleeve Anchors in place through the top hole, through the bottom hole into the concrete. Hammer them all the way in with a Punch or similar until you hear a “ting!”, that’s when the washer touches the extrusion, then they are firmly all the way down and in place. You will need a 13mm tube socket with a diameter of 20mm or less to fit through the top hole to fix the 10mm Sleeve Anchors nuts onto the 11mm bottom holes into the 10mm concrete holes. Tighten them up slowly until slightly firm and they grip. Sometimes, you get one that doesn’t grip, I do not know why, by at this point I have to take it out and add an epoxy glue to make sure it stays in place, as to not weaken all the rest of the length(s). $10 from the Warehouse is fine and sets in 5-20 minutes, enough to tighten it up again as to just before gripping, then wait for the glue to go off (meantime keep reading…). Walk and jump along the ramp length to possibly jiggle it down further to suit the variable undulations (concrete is never perfectly flat!). Go back to the first Sleeve Anchor and firmly tighten them all up from there – not too tight – my socket does a “click” when I then know it’s ‘just right’! From firm to tight, then an extra quarter turn I find. Lastly, and the best bit, put all the Black Nylon Hole Covers in the 20mm top holes to make it look sexy. Wipe all the surfaces down to get rid of the grease. Job done! Ready to go! You will forget it’s there after a week or so.
NB: Aluminium prices fluctuate, so please bear with us if the prices go up again (it is out of our control). Freight/shipping and custom or ‘tricky’ installation costs vary and are additional. All prices are +GST and are subject to change.
All 316 Stainless Steel fixings, hole covers & Installation included!
Displayed are a variety of different types on installations, Standard: Straight, Slightly Curved Convex and Slightly Curved Concave examples.
Plus a Complex Convex Curve and a Complex Concave Curve example to show you how we can install around corners or curved driveway entrances from the road side.
Installed KERBY™ Prices
Pre-Drilled, Fitted and Fully Installed for you – All 316 Stainless Steel fixings, hole covers & Installation included!
| Length | Detail | Price |
| 1m | 1x 1m length (2 Holes) for a Slightly Curved or a Standard Straight entry | $300+GST |
| 1.5m | 1x 1.5m length (3 Holes) for a Slightly Curved or a Standard Straight entry | $400+GST |
| 2m | 1x 2m length (3 Holes) for a Slightly Curved or a Standard Straight entry | $500+GST |
| 3m | 1x 3m length (4 Holes) for a Standard Straight entry | $700+GST |
| 4m–A | 1x 4m-A length (5 Holes) for a Standard Straight entry | $850+GST |
| 4m–B | 1x 3m + 1x 1m lengths (6 Holes) for a Standard Straight entry | $1,000+GST |
| 4m–C | 2x 2m lengths (6 Holes) for a Slightly Curved or a Standard Straight entry | $1,000+GST |
| 5m | 1x 4m-A + 1x 1m lengths (7 Holes) for a Standard Straight entry | $1,150+GST |
| 6m–A | 1x 4m-A + 1x 2m lengths (8 Holes) for a Standard Straight entry | $1,300+GST |
| 6m–B | 3x 2m lengths for a slight curve (9 Holes) for a Slightly Curved or a Standard Straight entry | $1,450+GST |
| 6m–C | 4× 1.5m lengths for an acute curve (12 Holes) for a Slightly Curved or a Standard Straight entry | $1,600+GST |
| 7m | 1x 4m-A + 1x 3m lengths (9 Holes) for a Standard Straight entry | $1,550+GST |
| 8m | 2x 4m-A lengths (10 Holes) for a Slightly Curved or a Standard Straight entry | $1,700+GST |
| 9m | 2x 4m-A + 1x 1m lengths (12 Holes) for a Standard Straight entry | $2,000+GST |
| 10m | 2x 4m-A + 1x 2m lengths (13 Holes) for a Standard Straight entry | $2,200+GST |
Full install means 1x site visit & all labour included.
Currently “INSTALLATION” areas are mainly Christchurch and Selwyn Urban areas only (established new subdivisions and land developments like Kajens Country, Fairfield Way area, Stonebrook area, East Maddisons Road areas, Othello Drive area, Little Rolleston Hamlet area, Woolshed Park area, Highgate area, Newmans Road area, Falcons Landing, Westwood Park area, Farringdon, Olivefields, Eastonfield, Acland Park, The Borough Green, Levi Park, and Branthwaite etc, Rolleston), Waimakariri (including Pegasus) and neighbouring districts. Rural and the wider Canterbury areas, and neighbouring regions all incur a call-out fee starting at $50+GST.
If you are outside of Canterbury, like Auckland for example, a friendly everyday builder can install KERBY™ with a concrete drill, a 10mm Concrete Drill and a 13mm tube socket for the M10X50 316 Stainless Steel DynaBolts (Sleeve Anchors) which are all included*.
NB: M10x50 316 Stainless Steel Sleeve-Anchors (Dynabolt fixings) and Nylon Dome Hole Covers to suit are all included in the price, supplied as per how many holes you have.
Installation means drilling holes in the concrete, using special tools to fix down the 316 Stainless Steel Dynabolts/Sleeve Anchors into the concrete (it is removable later by the way!), and finishing with special nylon dome hole covers to make it look sexy. So we deal with all the uneven concrete levels, the slight curves and irregularities that become apparent when we put a straight edge (the KERBY™) in place, and pack underneath with special wedges (unseen), to make it level and stable amongst doing all sorts of other things to make it long-lasting and hopefully perfect for you.
NB: Aluminium prices fluctuate, so please bear with us if the prices go up again (it is out of our control). Freight/shipping and custom or ‘tricky’ installation costs vary and are additional. All prices are +GST and are subject to change.
Cool Extras
ADDITIONAL EXTRAS
| Length | Detail | Price |
| Any length or lengths up to 10m | 1x Powder Coating Session | $150+GST |
We can powder coat any colour (subject to availability and application), to match the garage door and joinery, or make a statement in a bold safety colour.
Fun
| Length | Detail | Price |
| Any length or lengths up to 10m | 1x Glow-In-The-Dark Line (15mm-20mm inlay Sticker) in 15mm-20mm sticky tape inlay near the top, under the Nylon Dome Hole Covers (caps). | $50+GST |
| Durability TBC (untested at this point in time, but if it fails in 3 months, I will replace or refund). |
Safety
| Length | Detail | Price |
| Any length or lengths up to 10m | 1x Safety or Hazard or reflective Line in 15mm-20mm sticky tape (TBC) | $100+GST |
We can supply Kerby New Zealand Wide, even Australia!
Freight costs for one, two or three up to 2.4m lengths, 20kg or less for Christchurch to North Island or South Island Outside Christchurch Areas is around $50+GST. | Freight costs for one 2.5m-4.0m lengths, 20kg or less for Christchurch to North Island or South Island Outside Christchurch Areas varies at about $100+GST*. | Freight costs for two or three 2.5m-4.0m lengths, 25kg-50kg or less for Christchurch to North Island or South Island Outside Christchurch Areas varies at about $150+GST (depending on how many lengths)*.
*NB: Freight costs are calculated on your actual address and subject to change, see our quote/order form here.
KERBY.NZ is the Best Access Ramps that’s super-strong, simple & effective at eliminating that annoying bump when driving over the curb or your access in your driveway.
See what some of the many happy customers say about The Best Driveway Ramp…
Happy customers
Testimonials
“Don’t just take our word for it”…
KERBY™ – 12 Kestrel Street.
Thank you so much – super speedy install and it’s great! 😊
March 2023
KERBY™ – 7 Hauraki Rise
Most aesthicially pleasing.
Exactly what I needed. Bloody boil’, perfect, just right.
I am not scraping the front of my car anymore.
February 2023
KERBY™ – Driveway Crossing
I’d been looking for a suitable and practical driveway crossing installation to suit my wide curved driveway. I was pleasantly surprised to come across the “KERBY™” driveway ramp and made contact with the owner, Clint.
He came out and measured the number of sections required as well as determining what angles they needed to be cut, in order to fit smoothly across the width of the curved driveway. The installation was completed the following day without any issues.
I’m more than happy with the final result as there are now no nasty bumps when entering my driveway, but rather a smooth transition. I’d be more than happy to recommend Clint and his “KERBY™” ramps to anyone who asks.
January 2023
KERBY™ – Custom Instal
I checked the drive ramp.
Extremely nice work!
Thank you!
August 2022,
Custom Instal
KERBY™ – 724 Selwyn Road
Been testing it out this afternoon, great product, works well, very nicely installed, happy customer, thanks again Clint.
June 2022
KERBY™ – 28 Jean Archie Drive
Fantastic, better than expected. I’ll be happy to recommend Kerby to anyone who asks. Very well installed too I might add.
Thank you.
May 2022
Clint’s Custom Metal Flat Ramps are even better at Banishing That B@$tard Bump!
Super-Strong, Extra Smooth & Effective Driveway Kerb Access Ramps.
The Best Driveway Kerb Access Ramps that are the Best looking Aluminium Metal Flat Ramp around.
Customisable and suitable for almost all situations designed to nearly totally smooth out and stop that annoying bump and you bouncing, bottoming out or scraping your lowered car!
Want The Best FLAT PORTABLE or FIXED Metal Access Ramps for your home or business?
The Best Metal FLAT Access Ramps are designed right here in Rolleston (Selwyn, Christchurch NZ), custom made for your situation – to banish that bump and stop you bouncing and scraping!
Had enough of that b@$stard “bump” every time you go in or out of your driveway garage / shed / workshop? These customisable forklift ramps are for you. The best possible affordable customised FLAT Access Forklift Ramps in New Zealand – it’s better than awesome I reckon!
“Whatever the application these kerb ramp ideas for driveway curb ramps: Metal Driveway Ramps made from Aluminium extrusion, Flat Fixed access ramps, forklift ramps, curb ramps, roadside ramps, entry ramps, garage door entrance ramps, curb or kerb access driveway ramps for your garage, shed, workshop or yard or even wheelchair access. Business or residential. I can even make triangle custom ramps for caravan or motorhome for a full-height kerb – you name it, I can design and make it, it will work, I guarantee it!, just ask”.
GARAGE ENTRANCE RAMPS | DRIVEWAY RAMPS | DRIVEWAY KERB RAMP | GUTTER RAMP | CURB RAMPS | PORTABLE FLAT RAMPS | FIXED FLAT RAMPS | FORKLIFT RAMPS | GATE SLIDER COVERS | CUSTOM ACCESS RAMPS | THE BEST KERB RAMP IDEAS | METAL DRIVEWAY RAMP | Ramp Bunnings | Ramps Mitre 10 | Driveway Ramp nz
Clint's Custom Flat Car Driveway Ramps
The Absolute Best Fixed Flat Access Road-side Gutter Garage Driveway Entrance Kerb Ramps in NZ
Need quicker smoother, SAFER access via a Flat Fixed Gutter Kerb to Garage Road-Side Entrance Ramp?
These vehicle ramps eliminate that annoying cut-out and step-up in the gutter in the road.
These heavy duty 6mm Metal Driveway Ramps made from Aluminium Chequered Plate, Flat Fixed driveway access ramps solve many entrance approach problems as you drive in and out, stopping you bottoming out or scraping and damaging the bottom of your lowered car. Designed to make life easy as you come off the road into your garage, warehouse, shed or barn. Great for caravan access too! Clint’s Ramps look and perform the best and are far cheaper than most other products you can get to NZ. So support local, support NZ – Kiwi Made!
These Custom Flat Access Ramps do not rust and sag for the best possible looks and performance, plus can be customised to suit your space, and powder coated! Maximum 3m wide before I need to weld them together for larger entrances. Maximum 1490mm deep. I can even laser cut them to any shape – even curved! Check out 11 Logistics Drive‘s Curved Ramp that’s been laser cut to shape (image on the left).
Why damage your car every time you pull in or out of your garage?
Get over the garage kerb lip and drainage dip in front of your garage the easy way!
Clint's Forklift Ramps
The Absolute Best Warehouse, Business, Gate Slider Entrance Ramps
Need quicker smoother, SAFER access via a Flat Fixed Workshop Entrance Ramp?
These Heavy Duty High Quality Aluminium Metal Flat Fixed Forklift ramps solve many entry problems as you drive in and out with your precious loads.
Stopping bottoming out, scraping the bottom of your forklift, and makes for a far more stable load when going over that bump. Clint’s Forklift Ramps look and perform the best and is far cheaper than most other products in NZ. In fact I am not aware of anyone else doing this, so we’ll look after you with a good price.
Why risk loosing your load or damaging your load every time you pull in or out of your warehouse? Need to eliminate a Health & Safety risk or hazard?
Stop bottoming out, scraping, bouncing & bumping over the entrance kerb lip or Gate Slider rails in the yard and possibly loosing your load. Clint’s Forklift ramps are made in Rolleston Christchurch, NZ and can be installed locally at your place in a flash. Support local, support NZ!
These Flat Forklift Ramps made from high grade industrial Aluminium can be customised to suit your space, any size, any height. Awesome for eliminating the Sliding Gates’ roller rails on the ground! Even fully loaded trucks are no match for these solid and strong ramps.
Want to eliminate that annoying step-up in your warehouse, shed or barn?
Want to comply with Risk management and Health & Safety?
Clint's Portable Car Access Ramps
The Absolute Best Portable Garage Entrance Driveway Ramps that are portable and light.
Need quicker smoother, SAFER access via a Flat PORTABLE Garage Entrance Ramps that are temporary?
Why risk scraping and damaging your lowered car every time you pull in or out of your garage?
These Heavy Duty 6mm Aluminium Flat Portable driveway ramps solve many entrance problems as you drive in and out of your driveway to the garage, stopping you bottoming out or scraping the bottom or front of your car. Clint’s Portable Ramps look and perform the best and are far cheaper than most other products or re-doing the driveway concrete.
Stop bottoming out, scraping, bouncing & bumping over the garage curb dip and drainage grill in front of your garage. Clint’s driveway Access Portable ramps are made in Rolleston Christchurch, NZ and can be installed locally at your place in a flash. Elsewhere freighted for only about $50.
The Portable Access/ Entry Ramps pictured are 600mm x 800mm. This is the prototype and has been doubled up to 12mm. New Portable Ramps made will not have all the welds all over it. These ramps can be laser cut to any size and have any amount of shapes or handle holes cut out too. And you can powder coat them any colour! Best thing is they are very light and can be stored away after use.
Want to eliminate that annoying dip in your driveway and get back normality?